<div class="product-dosage"> <h2>Dosage</h2> <p>One test strip per test</p> </div> <hr class="bs-docs-separator" /> <div class="product-directions"> <h2>Directions</h2> <ol> <li>Remove a Baquacil Test Strip from bottle. Replace cap tightly.</li> <li>Dip strip into pool for one second and remove. Do not "swish" strip, as this will affect test accuracy. Do not shake excess water from test strip.</li> <li>Immediately compare Baquacil Oxidizer pad to color chart.</li> <li>After 15 seconds compare Baquacil Sanitizer and Algistat, ph and Total Alkalinity pads to color chart.</li> <li>Adjust readings within desired range. Follow label directions on each product.</li> </ol></div>

<p> </p>

<p> </p>

<h2>Product Dosage</h2><p>2 lb per 10,000 gallons of water.</p><hr><h2>Directions </h2><ul><li><p>Chemically clean the filter with Baquacil D.E &amp; Cartridge Filter Cleaner or Baquacil Sand Filter Cleaner - follow label directions on that product.</p></li><li><p>Slowly add Baquacil Line Clean at a rate of 2 lb per 10,000 gallons of water to the skimmer with the filter running. Do not add directly to the pool. This may cause the water to turn green.</p></li><li><p>Following the addition of Baquacil Line Clean, add Baquacil Flocculant as a filter aid per label directions and filter continuously for 24-48 hours until the pool is clear. Observe the pressure in the filter and backwash as necessary. Add Baquacil Oxidizer at a rate of 2 gallons per 10,000 gallons of water. Note: Pour into the pool in from of the skimmer. Do not add directly into the skimmer.</p></li><li><p>Immediately after the addition of the Oxidizer, add Baquacil CDX through the skimmer (1/2 gallon per 10,000 gallons). In order to maximize the effect of this treatment, it is very important to check the sanitizer level and top up with Baquacil Sanitizer and Algistat to maintain a reading of 50 ppm.</p></li><li><p>Run the filter continuously until the pool is clear.</p></li></ul><p>Note: A second treatment may be necessary if you see visible "debris" or "junk" entering the pool through the return jets. If no debris or junk is noticed and there is a greenish color returning to pool, no further treatment is ncessary. The greenish color should disappear withing 12-24 hours.</p>

<div id="product-dosage"> <h2>Product Dosage</h2> 8 fl oz per 10,000 gallons of water.</div> <hr class="bs-docs-separator" /> <div id="product-directions"> <h2>Directions</h2> <ol> <li>Before using this product, adjust total alkalinity and pH to the normal ranges using a reliable test kit or test strips.</li> <li>Set filter on re-circulate. If filter does not have a re-circulate setting, (cartridge or D.E. filters), remove cartridge or D.E. grids from filter prior to use.</li> <li>Raise the water level in the pool to the top of the skimmer box.</li> <li>With the pump running, slowly pour 8 fl oz of Baquacil Liquid Flocculant for every 10,000 gallons of pool water.</li> <li>Add the product directly into the pool water around the edges of the pool.</li> <li>Turn off the pump and allow suspended material to settle to the bottom of the pool. Leave the pump off and do not use the pool until cloudiness has settled, usually in 12-24 hours. If pool has a timer remove the "on tripper".</li> <li>Vacuum settled material to waste not to vacuum though the filter.</li> <li>Turn the filter back to filter setting or replace cartridge/D.E. grids and turn on pump.</li> <li>Check water balance and adjust as necessary.</li> </ol> <p>Baquacil Liquid Flocculant can be used with all sanitizer including Baquacil, chlorine, bromine and salt systems.</p> </div>