Fiberstars

Thermal Overload - All Units

Color Wheel Motor Assembly 1504 / 2004

Obsolete Fiberstars X-10 Receiver Module, C-R Unit Only

Fiberstars Lighted Rainfalls are designed to provide single rows of water and project them away from the falls lip at a 45 degree angle. The rows of water simulate the sound and effect of rain falling into the pool creating a unique and pleasant sound for you. The minimum water flow is between 5 and 8 GPM (gallons per minute). Keep in mind that as you increase the GPM flow rate, the further out the “rain” fall will extend from the wall of the pool. Our Lighted Rainfalls requires the least amount of fiber for the maximum amount of light output. Each one comes with 45’ of pre-attached fiber. <b>FEATURES & BENEFITS</b> • Brightening Shield Added • Hides point of light while reflecting light onto rain droplets. • Easy install

Fiberstars Lighted Rainfalls are designed to provide single rows of water and project them away from the falls lip at a 45 degree angle. The rows of water simulate the sound and effect of rain falling into the pool creating a unique and pleasant sound for you. The minimum water flow is between 5 and 8 GPM (gallons per minute). Keep in mind that as you increase the GPM flow rate, the further out the “rain” fall will extend from the wall of the pool. Our Lighted Rainfalls requires the least amount of fiber for the maximum amount of light output. Each one comes with 45’ of pre-attached fiber. <b>FEATURES & BENEFITS</b> • Brightening Shield Added • Hides point of light while reflecting light onto rain droplets. • Easy install

Fiberstars Lighted Rainfalls are designed to provide single rows of water and project them away from the falls lip at a 45 degree angle. The rows of water simulate the sound and effect of rain falling into the pool creating a unique and pleasant sound for you. The minimum water flow is between 5 and 8 GPM (gallons per minute). Keep in mind that as you increase the GPM flow rate, the further out the “rain” fall will extend from the wall of the pool. Our Lighted Rainfalls requires the least amount of fiber for the maximum amount of light output. Each one comes with 45’ of pre-attached fiber. <b>FEATURES & BENEFITS</b> • Brightening Shield Added • Hides point of light while reflecting light onto rain droplets. • Easy install

Fiberstars Lighted Rainfalls are designed to provide single rows of water and project them away from the falls lip at a 45 degree angle. The rows of water simulate the sound and effect of rain falling into the pool creating a unique and pleasant sound for you. The minimum water flow is between 5 and 8 GPM (gallons per minute). Keep in mind that as you increase the GPM flow rate, the further out the “rain” fall will extend from the wall of the pool. Our Lighted Rainfalls requires the least amount of fiber for the maximum amount of light output. Each one comes with 45’ of pre-attached fiber. <b>FEATURES & BENEFITS</b> • Brightening Shield Added • Hides point of light while reflecting light onto rain droplets. • Easy install

Fiberstars Lighted Rainfalls are designed to provide single rows of water and project them away from the falls lip at a 45 degree angle. The rows of water simulate the sound and effect of rain falling into the pool creating a unique and pleasant sound for you. The minimum water flow is between 5 and 8 GPM (gallons per minute). Keep in mind that as you increase the GPM flow rate, the further out the “rain” fall will extend from the wall of the pool. Our Lighted Rainfalls requires the least amount of fiber for the maximum amount of light output. Each one comes with 45’ of pre-attached fiber. <b>FEATURES & BENEFITS</b> • Brightening Shield Added • Hides point of light while reflecting light onto rain droplets. • Easy install

Replacement Antena

The Fiber Optic Bubbler has 75 Strands of Fiber. Perfect for sun shelves, swim outs, beach entry areas, or small fountain areas. Provide that splash of color in a flume of water approximately 3” - 5” above the water surface, when installed in no more than 4" - 6" of water. Fiberstars Bubbler Deluxe mounts flush on sun shelves, swim outs, etc. You can locate the bubbler just under or out of the water on fountains for two completely different effects. Each bubbler is preassembled for easy connection to a water supply line and a conduit connection for the fiber. The bubbler comes with 45’ of 75 strand fiber pre-attached. It has simple water flow requirements and needs 1-1/2” plumbing for water and 3/4” conduit for fiber. <b>FEATURES & BENEFITS</b> • The Lighted Bubbler Deluxe may be installed in many different methods and applications, such as: Flush with interior surface, raised off the surface area but with the tip under the water surface (typically fountains), or raised above the water surface (typically fountains). • The minimum flow rate is 8-10 GPM. 14-16 GPM for Supper Bubbler. • Easy install <b>BLK-DL-45</b> No inner pipe. 75 strands.

<p><b>NO FIBER INCLUDED</b> These beautiful Laminars are perfect for night time viewing either individually or in multiple arrangements. Fiberstars Large Laminar Flow Fountain comes with 20&rsquo; or 40&rsquo; of fiber preattached. It includes a Light Enhancement Device (built in), which is a fully adjustable device for increasing the light output in the water flow. The fiber and laminar are produced together for an optimum light output. For best lighting results, keep the water throw under 6&rsquo; up and 6&rsquo; out, for best lighting output you should aim these at the viewing area. DIMENSIONS OF DECK BOX: 19 3/4&rdquo; H x 13 1/2&rdquo; W. The deck box lids can be painted to your desired color. Use paint that is suitable for use on ABS materials. <b>NEW FEATURES:</b> &bull; Quick connect - disconnect water flow &bull; Better light output with direct drive LED only (no fiber) <b>SPECIFICATIONS:</b> &bull; Must have drain installed. &bull; The Large Laminars are designed for total water throws. Example : 6&rsquo; up, 6&rsquo; out 5&rsquo; up, 5&rsquo; out 4&rsquo; up, 4&rsquo; out</p>

<p>These beautiful Laminars are perfect for night time viewing either individually or in multiple arrangements. Fiberstars Large Laminar Flow Fountain comes with 20&rsquo; or 40&rsquo; of fiber preattached. It includes a Light Enhancement Device (built in), which is a fully adjustable device for increasing the light output in the water flow. The fiber and laminar are produced together for an optimum light output. For best lighting results, keep the water throw under 6&rsquo; up and 6&rsquo; out, for best lighting output you should aim these at the viewing area. DIMENSIONS OF DECK BOX: 19 3/4&rdquo; H x 13 1/2&rdquo; W. The deck box lids can be painted to your desired color. Use paint that is suitable for use on ABS materials. <b>NEW FEATURES:</b> &bull; Quick connect - disconnect water flow &bull; Better light output with direct drive LED only (no fiber) <b>SPECIFICATIONS:</b> &bull; Must have drain installed. &bull; The Large Laminars are designed for total water throws. Example : 6&rsquo; up, 6&rsquo; out 5&rsquo; up, 5&rsquo; out 4&rsquo; up, 4&rsquo; out</p>

These beautiful Laminars are perfect for night time viewing either individually or in multiple arrangements. Fiberstars Large Laminar Flow Fountain comes with 20’ or 40’ of fiber preattached. It includes a Light Enhancement Device (built in), which is a fully adjustable device for increasing the light output in the water flow. The fiber and laminar are produced together for an optimum light output. For best lighting results, keep the water throw under 6’ up and 6’ out, for best lighting output you should aim these at the viewing area. DIMENSIONS OF DECK BOX: 19 3/4” H x 13 1/2” W. The deck box lids can be painted to your desired color. Use paint that is suitable for use on ABS materials. <b>NEW FEATURES:</b> • Quick connect - disconnect water flow • Better light output with direct drive LED only (no fiber) <b>SPECIFICATIONS:</b> • Must have drain installed. • The Large Laminars are designed for total water throws. Example : 6’ up, 6’ out 5’ up, 5’ out 4’ up, 4’ out

42 Strand Cabled, By the Foot - Clear Jacket, Round - SPECIAL ORDER Use 2004, 2004-AS, 6004, 6004-AS or 409 Series Illuminators for best lighting

Concrete adapter for Fiberstars - LED Light, threads onto the light body - must use with FPAL-CA

<p>Lens Tightening Tool</p>

Fiber Glo Lens Only

<p>White Track - .82"X.34" 50'</p>

<p>50' White Bond Beam Track</p>

StarGlo fixtures are flexible and are great for lighting up rock waterfalls and landscape features. Using StarGlo fixtures (or kits) you can light areas of cascading water in the waterfall. The StarGlo fixtures should be placed above water level and pointed towards areas where the most water action will occur. This will typically be at the bottom of a waterfall with the StarGlopointed back towards the cascading water. <b>DO NOT place the StarGlo submerged under water! It is NOT a watertight fitting!</b>

StarGlo fixtures are flexible and are great for lighting up rock waterfalls and landscape features. Using StarGlo fixtures (or kits) you can light areas of cascading water in the waterfall. The StarGlo fixtures should be placed above water level and pointed towards areas where the most water action will occur. This will typically be at the bottom of a waterfall with the StarGlopointed back towards the cascading water. <b>DO NOT place the StarGlo submerged under water! It is NOT a watertight fitting!</b>

StarGlo fixtures are flexible and are great for lighting up rock waterfalls and landscape features. Using StarGlo fixtures (or kits) you can light areas of cascading water in the waterfall. The StarGlo fixtures should be placed above water level and pointed towards areas where the most water action will occur. This will typically be at the bottom of a waterfall with the StarGlopointed back towards the cascading water. <b>DO NOT place the StarGlo submerged under water! It is NOT a watertight fitting!</b>

StarGlo fixtures are flexible and are great for lighting up rock waterfalls and landscape features. Using StarGlo fixtures (or kits) you can light areas of cascading water in the waterfall. The StarGlo fixtures should be placed above water level and pointed towards areas where the most water action will occur. This will typically be at the bottom of a waterfall with the StarGlopointed back towards the cascading water. <b>DO NOT place the StarGlo submerged under water! It is NOT a watertight fitting!</b>

These Sealed Lens Kits are used with fiber that is 75 strands or less. Each KL2 lens assembly can only be used with a single jacket. <b>Kit includes:</b> Silicone Bushing (25 Strand), Silicone Bushing (50 Strand), Silicone Bushing (75 Strand), Lens, Lens Gasket, Compression Nut, Retaining Ring, 7/32” - 5/8” Clamp, and a Tie Rap (for 25 Strand Only)

<p>These Sealed Lens Kits are used with fiber that is 100 strands and above.Each KL2 lens assembly can only be used with a single jacket. <b>Kit Includes:</b> Silicone Bushing (100 Strand), Silicone Bushing (150 Strand), Silicone Bushing (225/300 Strand), Lens, Lens Gasket, Compression Nut, Retaining Ring, 7/32&rdquo; - 5/8&rdquo; Clamp (Up to 150 Strand), and a 1/2&rdquo; - 29/32&rdquo; Clamp (225/300 Strand)</p>

<p>Replacement Blades - Old Style X-ACTO (5 Pack)</p>

Fiberstars Lit Waterfall Light Bar Kit allows you to add color to waterfalls and rainfalls. This light bar easily mounts to the bottom lip of a sheer waterfall or rainfall, straight or radiused. There are two fibers per inch that aim down to light the water flow. A ¾” conduit is placed next to the waterfall so you can run fiber back to the illuminator. <b>NOTE:</b> For standard Light Bars, the fiber tail exits out of the left side. Reversed Light bars are now available (fiber tail exit on the right side). Add an “R” to the part numbers below. This will enable you to combine two lightbars to make 6’, 7’ and 8’ sizes. No additional cost. <b>FEATURES & BENEFITS</b> - Waterfall Light Bar light output is more dramatic on rainfalls vs. Sheerfalls

Fiberstars Lit Waterfall Light Bar Kit allows you to add color to waterfalls and rainfalls. This light bar easily mounts to the bottom lip of a sheer waterfall or rainfall, straight or radiused. There are two fibers per inch that aim down to light the water flow. A ¾” conduit is placed next to the waterfall so you can run fiber back to the illuminator. <b>NOTE:</b> For standard Light Bars, the fiber tail exits out of the left side. Reversed Light bars are now available (fiber tail exit on the right side). Add an “R” to the part numbers below. This will enable you to combine two lightbars to make 6’, 7’ and 8’ sizes. No additional cost. <b>FEATURES & BENEFITS</b> - Waterfall Light Bar light output is more dramatic on rainfalls vs. Sheerfalls

Fiberstars Lit Waterfall Light Bar Kit allows you to add color to waterfalls and rainfalls. This light bar easily mounts to the bottom lip of a sheer waterfall or rainfall, straight or radiused. There are two fibers per inch that aim down to light the water flow. A ¾” conduit is placed next to the waterfall so you can run fiber back to the illuminator. <b>NOTE:</b> For standard Light Bars, the fiber tail exits out of the left side. Reversed Light bars are now available (fiber tail exit on the right side). Add an “R” to the part numbers below. This will enable you to combine two lightbars to make 6’, 7’ and 8’ sizes. No additional cost. <b>FEATURES & BENEFITS</b> - Waterfall Light Bar light output is more dramatic on rainfalls vs. Sheerfalls

Fiberstars Lit Waterfall Light Bar Kit allows you to add color to waterfalls and rainfalls. This light bar easily mounts to the bottom lip of a sheer waterfall or rainfall, straight or radiused. There are two fibers per inch that aim down to light the water flow. A ¾” conduit is placed next to the waterfall so you can run fiber back to the illuminator. <b>NOTE:</b> For standard Light Bars, the fiber tail exits out of the left side. Reversed Light bars are now available (fiber tail exit on the right side). Add an “R” to the part numbers below. This will enable you to combine two lightbars to make 6’, 7’ and 8’ sizes. No additional cost. <b>FEATURES & BENEFITS</b> - Waterfall Light Bar light output is more dramatic on rainfalls vs. Sheerfalls

Fiberstars Lit Waterfall Light Bar Kit allows you to add color to waterfalls and rainfalls. This light bar easily mounts to the bottom lip of a sheer waterfall or rainfall, straight or radiused. There are two fibers per inch that aim down to light the water flow. A ¾” conduit is placed next to the waterfall so you can run fiber back to the illuminator. <b>NOTE:</b> For standard Light Bars, the fiber tail exits out of the left side. Reversed Light bars are now available (fiber tail exit on the right side). Add an “R” to the part numbers below. This will enable you to combine two lightbars to make 6’, 7’ and 8’ sizes. No additional cost. <b>FEATURES & BENEFITS</b> - Waterfall Light Bar light output is more dramatic on rainfalls vs. Sheerfalls

Fiberstars Lit Waterfall Light Bar Kit allows you to add color to waterfalls and rainfalls. This light bar easily mounts to the bottom lip of a sheer waterfall or rainfall, straight or radiused. There are two fibers per inch that aim down to light the water flow. A ¾” conduit is placed next to the waterfall so you can run fiber back to the illuminator. <b>NOTE:</b> For standard Light Bars, the fiber tail exits out of the left side. Reversed Light bars are now available (fiber tail exit on the right side). Add an “R” to the part numbers below. This will enable you to combine two lightbars to make 6’, 7’ and 8’ sizes. No additional cost. <b>FEATURES & BENEFITS</b> - Waterfall Light Bar light output is more dramatic on rainfalls vs. Sheerfalls

Fiberstars Lit Waterfall Light Bar Kit allows you to add color to waterfalls and rainfalls. This light bar easily mounts to the bottom lip of a sheer waterfall or rainfall, straight or radiused. There are two fibers per inch that aim down to light the water flow. A ¾” conduit is placed next to the waterfall so you can run fiber back to the illuminator. <b>NOTE:</b> For standard Light Bars, the fiber tail exits out of the left side. Reversed Light bars are now available (fiber tail exit on the right side). Add an “R” to the part numbers below. This will enable you to combine two lightbars to make 6’, 7’ and 8’ sizes. No additional cost. <b>FEATURES & BENEFITS</b> - Waterfall Light Bar light output is more dramatic on rainfalls vs. Sheerfalls

Fiberstars Lit Waterfall Light Bar Kit allows you to add color to waterfalls and rainfalls. This light bar easily mounts to the bottom lip of a sheer waterfall or rainfall, straight or radiused. There are two fibers per inch that aim down to light the water flow. A ¾” conduit is placed next to the waterfall so you can run fiber back to the illuminator. <b>NOTE:</b> For standard Light Bars, the fiber tail exits out of the left side. Reversed Light bars are now available (fiber tail exit on the right side). Add an “R” to the part numbers below. This will enable you to combine two lightbars to make 6’, 7’ and 8’ sizes. No additional cost. <b>FEATURES & BENEFITS</b> - Waterfall Light Bar light output is more dramatic on rainfalls vs. Sheerfalls

Fiberstars Lit Waterfall Light Bar Kit allows you to add color to waterfalls and rainfalls. This light bar easily mounts to the bottom lip of a sheer waterfall or rainfall, straight or radiused. There are two fibers per inch that aim down to light the water flow. A ¾” conduit is placed next to the waterfall so you can run fiber back to the illuminator. <b>NOTE:</b> For standard Light Bars, the fiber tail exits out of the left side. Reversed Light bars are now available (fiber tail exit on the right side). Add an “R” to the part numbers below. This will enable you to combine two lightbars to make 6’, 7’ and 8’ sizes. No additional cost. <b>FEATURES & BENEFITS</b> - Waterfall Light Bar light output is more dramatic on rainfalls vs. Sheerfalls

Fiberstars Lit Waterfall Light Bar Kit allows you to add color to waterfalls and rainfalls. This light bar easily mounts to the bottom lip of a sheer waterfall or rainfall, straight or radiused. There are two fibers per inch that aim down to light the water flow. A ¾” conduit is placed next to the waterfall so you can run fiber back to the illuminator. <b>NOTE:</b> For standard Light Bars, the fiber tail exits out of the left side. Reversed Light bars are now available (fiber tail exit on the right side). Add an “R” to the part numbers below. This will enable you to combine two lightbars to make 6’, 7’ and 8’ sizes. No additional cost. <b>FEATURES & BENEFITS</b> - Waterfall Light Bar light output is more dramatic on rainfalls vs. Sheerfalls

Fiberstars Lit Waterfall Light Bar Kit allows you to add color to waterfalls and rainfalls. This light bar easily mounts to the bottom lip of a sheer waterfall or rainfall, straight or radiused. There are two fibers per inch that aim down to light the water flow. A ¾” conduit is placed next to the waterfall so you can run fiber back to the illuminator. <b>NOTE:</b> For standard Light Bars, the fiber tail exits out of the left side. Reversed Light bars are now available (fiber tail exit on the right side). Add an “R” to the part numbers below. This will enable you to combine two lightbars to make 6’, 7’ and 8’ sizes. No additional cost. <b>FEATURES & BENEFITS</b> - Waterfall Light Bar light output is more dramatic on rainfalls vs. Sheerfalls <em>Use 2004, 2004-AS, 6004, 6004-AS or 409 Series Illuminators for best lighting.</em>

<p>When purchasing Fiber Kits, you need to purchase ONLY the Lens Housings. If you purchase Fiber in Bulk rolls or lengths, you need to purchase BOTH the Lens Housings and Sealed Lens Kits. These lens housings glue onto 1-½” PVC pipe. Our Sealed Lens Kits (included on all fiber kits) seats in the housing. 1-½” slip connection. Includes: Lens Housing only. NO LENS INCLUDED</p>

<p>Butane Hot Knife</p>

Fiberstix Landscape Fixture. Includes 6" PVC Stake For Installation in the Ground. Use with 3 Strand FSPT-3 Fiber. For Runs Over 50' Use 12 Strand BAF Fiber.

Fiberstars Fiber Optics Fiber Kit 300 Strand 14' Part B300KL2-14

Cabled fiber in a flat black design. The 42 strand cabled fiber and put it in the FSSB casing for the easiest to use cabled fiber ever.

42 Strand Cabled, 150’ Roll - Clear Jacket, Round Use 2004, 2004-AS, 6004, 6004-AS or 409 Series Illuminators for best lighting

42 Strand Cabled, 125’ Roll - Clear Jacket, Round Use 2004, 2004-AS, 6004, 6004-AS or 409 Series Illuminators for best lighting.

42 Strand Cabled, 500’ Roll - Clear Jacket, Round Use 2004, 2004-AS, 6004, 6004-AS or 409 Series Illuminators for best lighting

Cabled fiber in a flat black design. The 42 strand cabled fiber and put it in the FSSB casing for the easiest to use cabled fiber ever.

42 Strand Cabled, 200’ Roll - Clear Jacket, Round Use 2004, 2004-AS, 6004, 6004-AS or 409 Series Illuminators for best lighting

Cabled fiber in a flat black design. The 42 strand cabled fiber and put it in the FSSB casing for the easiest to use cabled fiber ever.