spa-parts

<p>The Clean &amp; Clear Plus Filter combines top-end filter performance with low maintenance. This dependable design uses special filter elements to strip tiny particles from your pool water, some as small as 20 microns (an average grain of beach sand is 1,000 microns). Our four-cartridge design provides maximum filter surface area to capture more dirt and extend time between cleanings. And cleaning is a snap—open the top, remove the cartridges, hose them off and the Clean &amp; Clear Plus Filter is ready to go again. Includes Cartridge, Pressure Gauge, Union Kit and Air Relief Valve. </p>

<p>The Clean &amp; Clear Plus Filter combines top-end filter performance with low maintenance. This dependable design uses special filter elements to strip tiny particles from your pool water, some as small as 20 microns (an average grain of beach sand is 1,000 microns). Our four-cartridge design provides maximum filter surface area to capture more dirt and extend time between cleanings. And cleaning is a snap—open the top, remove the cartridges, hose them off and the Clean &amp; Clear Plus Filter is ready to go again. Includes Cartridge, Pressure Gauge, Union Kit and Air Relief Valve. </p>

<p>FNS Plus filters have been designed with curved grids to maximize filtration area. More filter area means better performance and longer periods between cleanings. Our internal design has been refined to minimize flow restrictions and, therefore, requires minimal pumping power to achieve a needed flow rate. That means lower utility costs.</p><p></p><p>• Curved vertical grids provide maximum filter surface area for greater dirt-trapping capacity and longer periods between cleanings.</p><p>• Internal design ensures optimum filtration and backwashing efficiency.</p><p>• Chemical-resistant, fiberglass-reinforced polypropylene tank for exceptional strength and longer life.</p><p>• Easily removable filter grid pack to simplify maintenance and save you time. </p>

<p>The Clean &amp; Clear Plus Filter combines top-end filter performance with low maintenance. This dependable design uses special filter elements to strip tiny particles from your pool water, some as small as 20 microns (an average grain of beach sand is 1,000 microns). Our four-cartridge design provides maximum filter surface area to capture more dirt and extend time between cleanings. And cleaning is a snap—open the top, remove the cartridges, hose them off and the Clean &amp; Clear Plus Filter is ready to go again. Includes Cartridge, Pressure Gauge, Union Kit and Air Relief Valve. </p>

<p>The Spa Eclipse Next Generation Corona Discharge system matches the capabilities of DEL Ozone's High Output units at a fraction of the size. Featuring DEL’s exclusive Advanced Plasma Gap technology, the newly engineered design is now equipped with Auto Voltage Sensing. It’s the reliability, performance and technological advancement you can only expect from DEL Ozone. <strong>**REPLACES PREVIOUS SPA ECLIPSE MODEL** **REPLACES PREVIOUS CDS-16 MODEL**</strong></p><ul><li><p>Water Back Flow Resistant</p></li><li><p>Auto Voltage Sensing</p></li><li><p>100-250V / 50-60Hz</p></li><li><p>Consistent Ozone Output</p></li><li><p>Ozone LED Indicator Light</p></li><li><p>Reduced Nitric Acid By-Product</p></li><li><p>Utilizes Ozone Resistant Materials</p></li><li><p>Comes with AMP plug (pictured above)</p></li><li><p>ECS-1RPAM2-U</p></li></ul>

<ul><li><p>True continuous rated horsepower of 1.5, 2.0, 2.5 and 3.0 HP</p></li><li><p>48-Frame or 56-Frame, Single or Dual Speed (energy saving)</p></li><li><p>Use more jets per pump</p></li><li><p>Same physical size as Aqua-Flo XP2, XP2e (fits within the same volume envelope)</p></li><li><p>Can be used as substitute or retrofit to Aqua-Flo model XP2 or XP2e pumps and similar pumps and wet ends offered by other domestic and foreign suppliers</p></li><li><p>Made in USA from highest quality materials with</p></li><li><p>UL and CUL certifications</p></li><li><p>CE and TUV certification on export pumps to ensure product performance for you and your customers</p></li><li><p>Equipped with the highest quality Viton Seals</p></li><li><p>Equipped with high efficiency electrical motors, custom designed for Spa applications </p></li></ul>

<p>Clean &amp; Clear Plus Cartridge Pool Filters have a corrosion-resistant, injection-molded, fiberglass-reinforced, polypropylene filter tank featuring superior strength and reliability. The cartridge assembly uses four, nonwoven, polyester cartridges. There is no need for backwashing. Simply remove the cartridges and rinse with a garden hose, reducing water consumption. </p>

<li>True continuous rated horsepower of 1.5, 2.0, 2.5 and 3.0 HP <li>48-Frame or 56-Frame, Single or Dual Speed (energy saving) <li>Use more jets per pump <li>Same physical size as Aqua-Flo XP2, XP2e (fits within the same volume envelope) <li>Can be used as substitute or retrofit to Aqua-Flo model XP2 or XP2e pumps and similar pumps and wet ends offered byother domestic and foreign suppliers <li>Made in USA from highest quality materials with <li>UL and CUL certifications <li>CE and TUV certification on export pumps to ensure product performance <li>Equipped with the highest quality Viton Seals <li>Equipped with high efficiency electrical motors, custom designed for Spa application

<li>True continuous rated horsepower of 1.5, 2.0, 2.5 and 3.0 HP <li>48-Frame or 56-Frame, Single or Dual Speed (energy saving) <li>Use more jets per pump <li>Same physical size as Aqua-Flo XP2, XP2e (fits within the same volume envelope) <li>Can be used as substitute or retrofit to Aqua-Flo model XP2 or XP2e pumps and similar pumps and wet ends offered by other domestic and foreign suppliers <li>Made in USA from highest quality materials with <li>UL and CUL certifications <li>CE and TUV certification on export pumps to ensure product performance for you and your customers <li>Equipped with the highest quality Viton Seals <li>Equipped with high efficiency electrical motors, custom designed for Spa applications

Waterway Pump EX2, 3.0HP, 230V, 10.0A, 1-Speed, 2"MBT, SD, 48-Frame, 11Amp

<li>True continuous rated horsepower of 1.5, 2.0, 2.5 and 3.0 HP <li>48-Frame or 56-Frame, Single or Dual Speed (energy saving) <li>Use more jets per pump <li>Same physical size as Aqua-Flo XP2, XP2e (fits within the same volume envelope) <li>Can be used as substitute or retrofit to Aqua-Flo model XP2 or XP2e pumps and similar pumps and wet ends offered by other domestic and foreign suppliers <li>Made in USA from highest quality materials with <li>UL and CUL certifications <li>CE and TUV certification on export pumps to ensure product performance for you and your customers <li>Equipped with the highest quality Viton Seals <li>Equipped with high efficiency electrical motors, custom designed for Spa applications

<p>Blue-White Industries F300 Series Flowmeter for 2"  PVC Pipe...SCH 40  Standard Flow 20 - 120 GPM or SCH 80  Standard Flow <span>18 – 100 GPM  </span>Requires 20" uninterrupted upstream piping prior to flowmeter and 8" uninterrupted downstream after flowmeter for proper installation. Replacement gasket F-3003, see related products below. Included in the box are two stainless steel clamps and F-3003 seal gasket.</p>

Generic replacement filter cartridge for Jacuzzi CFT25 & CFR 25 model filters. Unicel: C5625 Filber: FC1425 Pleatco: PJ25 Dimensions Diameter: 5" Length: 13-1/4" Top Style: Open Top ID: 2-3/8' Bottom Style: Open Bottom ID: 2-3/8"

<p>Grundfos Circulating Pump circulates 12-18 gallons per minute. 115V, 1-inch barb. Part number: 59896291</p>

AquaFlo XP2e Pump, 2.0 Operational HP/3.0 Total HO, 230v, 2-spd, 48fr motor, 2", OEM. Note: In 2012, the manufacturer changed the way Aquaflo pumps are rated. These pumps are now assigned both an operational horsepower (ohp), and a total horsepower (thp) rating. Previous versions of these pumps used only the operational horsepower. If you are replacing an older Aquaflo pump, be sure to match the operational hp rating rather than the total hp.

<p>The Clean &amp; Clear Plus Filter combines top-end filter performance with low maintenance. This dependable design uses special filter elements to strip tiny particles from your pool water, some as small as 20 microns (an average grain of beach sand is 1,000 microns). Our four-cartridge design provides maximum filter surface area to capture more dirt and extend time between cleanings. And cleaning is a snap—open the top, remove the cartridges, hose them off and the Clean &amp; Clear Plus Filter is ready to go again. Includes Cartridge, Pressure Gauge, Union Kit and Air Relief Valve. </p>

1/16HP Tiny Mite Complete Side Discharge Wet End. 1" MBT plumbing size.

Replacement Gasket, 3-5/16" OD, 2-3/4" ID, for 3" Heater Tube

<p>Grundfos Circulating Pump circulates 12-18 gallons per minute. 230V, 1-inch barb. Part number: 59896292</p>

Complete side discharge wet end for 6HP Power Right Cal Spas pump. Fits 48 frame motors. 2" plumbing size.

<p>F-300 Series for 1-1/2" Pipe. Machined Acrylic Flowmeter, Standard Flow operates from 10 to 70 GPM. Fits standard SCH40 and SCH80 1.5" PVC Pipe.</p>

Aquatemp Products Heater Uni-Nut for 3" Heater Tube, 4" OD, 3-5/8" Threads, 3-3/8" Inside Flange

Replacement Sundance Spas / Jacuzzi Curled Style Temperature Sensor designed to fit LX10, LX15, 701 & 724 series. This is a new, OEM part, number: 6600-166.

<p>Complete side discharge wet end for 2.5HP FMXP2e pump. Fits 56Y frame motors. 2" plumbing size.</p>

<p>Balboa Bath Pump 5.5 Amp 115V 1 Speed w/Air Switch &amp; Cord, 1050031 </p><p>Balboa / Pentair bath WOW pump includes air switch and 115V nema cord.</p><ul><li><p>Voltage: 115V</p></li><li><p>Amperage: 5.5</p></li><li><p>Horsepower: .50GPM: 65</p></li><li><p>Intake: 1-1/2"</p></li><li><p>Discharge: 1-1/2" Self draining volute.</p></li></ul><p>Length: 13-1/2"</p><p>Width: 4-7/8"</p><p>Height: 7-1/4"</p><p></p>

Heater Uni-Nut 2" for 2-1/4" Housings, used on Sunbelt Spas

<ul> <li>Coates 11kW, 240V, 46 amp, Single Phase Spa Heater</li> <li>Built-in pressure switch prevents operation when there is no water flow and allows operation at flow rates between 15GPM and 80GPM.</li> <li>Stainless steel tank is designed to optimize heat transfer by directing the water flow over the incoloy elements efficiently.</li> <li> <h2>Dimensions:</h2> ST : 17-1/2"L x 4"W x 14"</li> </ul>

Sundance Spas High Limit Sensor designed to fit 800, 600, 600-S, 600-DX, 400, and 1992 Suncoast Systems. Part number: SD6600-110.

Replacement SC30 30 Amp Slo-Blo Fuse.

Replacement SC-25 25 Amp Slo-Blo Fuse.

Waterway Filter Lid Top, for Spas and Hot Tubs. Features 2 Cup Holders, Black Color.

Self-draining center discharge complete wet end for 1.5HP TMCP bath pump. 1-1/2" plumbing size.

Replacement 20 Amp Slow-Blo Fuse.

Complete side discharge wet end for 3HP Ultimax pump. Fits 48 & 56 frame motors. 2" plumbing size.

Complete side discharge wet end for 4HP Power Right pump. Fits 48 frame motors. 2" plumbing size.

<p>Balboa Dura-Jet Pump, 48 Frame 2.0HP 2 Speed 115V, DJAYFA, 4239113-S</p><p>The Dura Jet Style by Balboa Water Group - pumps have earned a reputation for consistent quality and long service life. The wetend provides Multi-directional volute mountings and a 3 position drain plug for complete flexibility of configuration.</p>

<p>11KW ELS 1102-2 Electric 240 Volt Spa Hot Tub Heater</p>

Replacement Pressure Switch 3029, 25A, Tecmark, 1/8 Male Pile Threaded Fitting, SPNO. Series 3000 this switch is found in many spa applications where a durable pressure switch is required. It is rated at 25 amps and is available in a variety of mounting styles.

Sundance Spas new style box end temperature sensor designed to fit 800,600,600-S,400S series. Part number: SD6600-167

Complete side discharge wet end for 3HP Executive Pump. Fits 56Y frame motors. 2-1/2" plumbing size.

<p><strong>Balboa 1070021 Circulation Pump – Reliable Spa Water Flow</strong><br>The <strong>Balboa 1070021 Circulation Pump</strong> is a durable, high-quality 1-speed pump designed to keep spa and hot tub water circulating efficiently. With a <strong>0.25 HP motor</strong> and <strong>230 V power</strong>, this compact pump delivers consistent flow to help maintain clean, properly heated water. Built with a long <strong>120" AMP cord</strong> and a standard 10-frame design, it’s a dependable replacement for models like 1030056 and 1070056. Perfect for residential spa owners needing a straightforward, reliable replacement circulation pump.</p>

<p>1.5 HP 230V 2 Speed Flo-Master XP2 Pump. The Flo-Master XP2 Series, Aqua-Flo by Gecko is a high performance spa pump. XP2 offers high performance while utilizing the same space requirements as most other applications. 2" inlets and outlets.</p>

<p>The Laing Thermotech pump consumes 40% less energy than standard pumps, providing 150 watts of performance using only 108 watts of power. The compact design and open impeller design make this pump easy to install and resistant to clogging. This pump also features Dry-Run Protection.</p>

4HP Super Flo Pump Wet End. Side discharge - 2-1/2" inlet x 2" outlet 46 frame motor.

75 SQFT RTL75 Dynamic Series II Top Load Cartridge Filter & Chlorine/Bromine Dispenser. 75 SQFT filtration area. 2" SLIP plumbing fittings. 25" overall height.

Complete side discharge wet end for 1.5HP JWB pumps. Fits 56 frame motors. 1-1/2" plumbing size.

Complete side discharge wet end for 1.5HP Ultimax pump. Fits 48 & 56 frame motors. 2" plumbing size.

Leviton 20 Amp GFCI w/ Power Cord, 120V