Poolife

<p>Poolife Gold Metal Clarifier is a highly concentrated clarifying formula and should be diluted before added to the pool. Add the correct clarifier dosage to a pail filled with pool water (water in pail will turn blue). Then apply entire clarifier mixture into pool around inside pool edge. Circulate water for several hours. <br><br>Initial Treatment: 1 fl oz per 6,000 gallons. <br>For very cloudy water use 1 fl oz. per 3,000 gallons. <br><br>Maintenance Treatment: 1 fl oz per 6,000 gallons every week for heavy swimmer load. For light swimmer load, apply 1 fl oz per 6,000 gallons every 2 weeks. <br><br>For best results use Poolife Gold Metal Clarifier regularly, especially after filter backwashing or cleaning, after algaecide treatment to remove dead algae without vacuuming and following shock treatment.</p>

<h2></h2><p>Poolife Intensive Stain Prevention prevents staining and scaling in your pool water. This concentrated formula works great at protecting your pool against scale, stain and rust caused by minerals and metals in the water. </p><hr><h2>Dosage</h2><h3>Initial Dose:</h3><p>16 fl oz per 10,000 gallons of water.</p><h3>Preventative Maintenance:</h3><p>4 fl oz per 10,000 gallons of water per week.</p><h3>Metal Treatment:</h3><p>32 fl oz per 10,000 gallons of pool water.</p><hr><h2>Directions</h2><p>When pool is initially filled, Poolife Intensive Stain Prevention should always be added because fresh water supplies usually contain stain and scale producing minerals such as copper, iron, manganese and calcium.</p><p>For best results, add the required amount of Poolife Intensive Stain Prevention at the time you start to fill the pool, not after the pool is filled.</p><p>After Poolife Intensive Stain Prevention has been added and the pool filled, filter and circulate the water at least overnight before adding chlorine or other pool chemicals to allow it to react with and prevent precipitation of mineral in fresh water.</p><p>It is best to add poolife intensive stain prevention at dusk.</p><p>Do not use this product within 8 hours of the addition of shock products.</p><h3>Initial Treatment:</h3><ul><li><p>Add 16 fl oz per 10,000 gallons of water to normal hardness and mineral content.</p></li><li><p>If the water hardness is over 200 ppm or has high iron copper or manganese content (over 0.1 ppm) double the intial dosage.</p></li></ul><h3>Preventative Maintenance:</h3><p>For preventative maintenance, add 4 fl oz per 10,000 gallons of pool water once a week during the swimming season, regardless of make-up water, to take care of top up water.</p><h3>Metal Treatment:</h3><p>When metals are detected in your pool water, add 32 fl oz per 10,000 gallons of water. Continue wiht a preventative maintenance dosage throughout the swimming season.</p>

<div class="descriptionunder reading-container"> <div class="product-description"> <h2>Description</h2> <p>The Poolife Pods Stabilizer and Conditioner is designed to make adding products easier. Simply drop in to add the pre-measured pouches into your pool, and the pool pump circulation will do the rest.</p> </div> <hr class="bs-docs-separator" /> <div class="product-bullet-points"> <ul> <li>Pre-Measured pouches for the perfect amount of product</li> <li>Quick and easy application</li> <li>Pods are completely water soluble</li> </ul> </div> <hr class="bs-docs-separator" /> <div class="product-dosage"> <h2>Dosage</h2> <p>Below is a list of pod additions for each pool size to raise stabilizer (cyanic acid) levels 10 ppm:</p> <ul> <li>5,000 gal pool - 1 pod</li> <li>10,000 gal pool - 2 pods</li> <li>15,000 gal pool - 3 pods</li> <li>20,000 gal pool - 4 pods</li> <li>25,000 gal pool - 5 pods</li> </ul> </div> <hr class="bs-docs-separator" /> <div class="product-directions"> <h2>Directions</h2> <p>This product aids to protect chlorine in pool water. It diminishes the loss of chlorine caused by sunlight. Use the product if sunlight makes it stubborn to maintain the correct chlorine level.</p> <ol> <li>Clean and backwash the filter.</li> <li>Adjust the free available chlorine (FAC) level to 1-4 parts per million (ppm).</li> <li>Measure the stabilizer (cyanuric acid) concentration. The ideal range is 20 - 40 ppm. The chlorine is not as effective if the range is above 90 ppm.</li> <li>Be sure the skimmer is clean and free of all chemical residue or debris.</li> <li>Add 1 pod directly into the pool skimmer while the pump is running. Allow the pod to dissolve before adding additional pods or other products. Only add one pod at a time.</li> <li>Leave the circulation pump running and <strong>DO NOT</strong> backwash for 4 hours.</li> <li>Use the list above to determine the correct amount of this product to use.</li> </ol></div> <hr class="bs-docs-separator" /> <div class="product-ingredients"> <h2>Ingredients</h2> <p><strong>Cyanuric Acid:</strong> 98.5%</p> <p><strong>Constituents Ineffective As Adjuvants:</strong> 1.5%</p> </div> </div> <div> <div class="yotpo yotpo-main-widget" data-product-id="1643865964614" data-name="Poolife Pods Stabilizer and Conditioner" data-url="https://www.poolgeek.com/products/poolife-pods-stabilizer-and-conditioner" data-image-url="//cdn.shopify.com/s/files/1/0099/3802/products/PoolifePodsSTAB_large.jpg%3Fv=1539189113" data-description="&lt;div class=&quot;product-description&quot;&gt; &lt;h2&gt;Description&lt;/h2&gt; &lt;p&gt;The Poolife Pods Stabilizer and Conditioner is designed to make adding products easier. Simply drop in to add the pre-measured pouches into your pool, and the pool pump circulation will do the rest.&lt;/p&gt; &lt;/div&gt; &lt;!-- product-description --&gt; &lt;hr class=&quot;bs-docs-separator&quot;&gt; &lt;div class=&quot;product-bullet-points&quot;&gt; &lt;ul&gt; &lt;li&gt;Pre-Measured pouches for the perfect amount of product&lt;/li&gt; &lt;li&gt;Quick and easy application&lt;/li&gt; &lt;li&gt;Pods are completely water soluble&lt;/li&gt; &lt;/ul&gt; &lt;/div&gt; &lt;!--product-bullet-points --&gt; &lt;hr class=&quot;bs-docs-separator&quot;&gt; &lt;div class=&quot;product-dosage&quot;&gt; &lt;h2&gt;Dosage&lt;/h2&gt; &lt;p&gt;Below is a list of pod additions for each pool size to raise stabilizer (cyanic acid) levels 10 ppm:&lt;/p&gt; &lt;ul&gt; &lt;li&gt;5,000 gal pool - 1 pod&lt;/li&gt; &lt;li&gt;10,000 gal pool - 2 pods&lt;/li&gt; &lt;li&gt;15,000 gal pool - 3 pods&lt;/li&gt; &lt;li&gt;20,000 gal pool - 4 pods&lt;/li&gt; &lt;li&gt;25,000 gal pool - 5 pods&lt;/li&gt; &lt;/ul&gt; &lt;/div&gt; &lt;!-- product-dosage --&gt; &lt;hr class=&quot;bs-docs-separator&quot;&gt; &lt;div class=&quot;product-directions&quot;&gt; &lt;h2&gt;Directions&lt;/h2&gt; &lt;p&gt;This product helps to protect chlorine in pool water. It stops the loss of chlorine caused by sunlight. Use the product if sunlight makes it difficult to maintain the correct chlorine level.&lt;/p&gt; &lt;ol&gt; &lt;li&gt;Clean and backwash the filter.&lt;/li&gt; &lt;li&gt;Adjust the free available chlorine (FAC) level to 1-4 parts per million (ppm).&lt;/li&gt; &lt;li&gt;Measure the stabilizer (cyanuric acid) concentration. The ideal range is 20 - 40 ppm. The chlorine is not as effective if the range is above 90 ppm.&lt;/li&gt; &lt;li&gt;Be sure the skimmer is clean and free of all chemical residue or debris.&lt;/li&gt; &lt;li&gt;Add 1 pod directly into the pool skimmer while the pump is running. Allow the pod to dissolve before adding additional pods or other products. Only add one pod at a time.&lt;/li&gt; &lt;li&gt;Leave the circulation pump running and &lt;strong&gt;DO NOT&lt;/strong&gt; backwash for 4 hours.&lt;/li&gt; &lt;li&gt;Use the list above to determine the correct amount of this product to use.&lt;/li&gt; &lt;/ol&gt; &lt;/div&gt; &lt;!--product-directions --&gt; &lt;hr class=&quot;bs-docs-separator&quot;&gt; &lt;div class=&quot;product-ingredients&quot;&gt; &lt;h2&gt;Ingredients&lt;/h2&gt; &lt;p&gt;&lt;strong&gt;Cyanuric Acid:&lt;/strong&gt; 98.5%&lt;/p&gt; &lt;p&gt;&lt;strong&gt;Constituents Ineffective As Adjuvants:&lt;/strong&gt; 1.5%&lt;/p&gt; &lt;/div&gt; &lt;!--product-ingredients --&gt; &lt;hr class=&quot;bs-docs-separator&quot;&gt;" data-yotpo-element-id="1"> <div class="main-widget yotpo-display-wrapper yotpo-no-reviews"> <div class="yotpo-label yotpo-small-box "></div> </div> </div> </div>

<div class="product-description"> <h2>Description</h2> <p>The Poolife pH Plus Pods are designed to make adding products easier. Simply drop in to add the pre-measured pouches into your pool, and the pool pump circulation will finish the rest.</p> </div> <hr class="bs-docs-separator" /> <div class="product-bullet-points"> <ul> <li>Pre-Measured pouches for the perfect amount of product</li> <li>Quick and easy application</li> <li>Pods are completely water soluble</li> </ul> </div> <hr class="bs-docs-separator" /> <div class="product-dosage"> <h2>Dosage</h2> <p>Below is a list of the pouch addition quantities:</p> <h3>If the pH is below 7.0:</h3> <ul> <li>10,000 gal - 1 Pod</li> <li>20,000 gal - 2 Pods</li> <li>30,000 gal - 3 Pods</li> </ul> <h3>If the pH is below 6.6:</h3> <ul> <li>10,000 gal - 5 Pods</li> <li>20,000 gal - 8 Pods</li> <li>30,000 gal - 10 Pods</li> </ul> <h3>If the pH is below 6.4:</h3> <ul> <li>10,000 gal - 8 Pods</li> <li>20,000 gal - 12 Pods</li> <li>30,000 gal - 16 Pods</li> </ul> </div> <hr class="bs-docs-separator" /> <div class="product-directions"> <h2>Directions</h2> <p>To keep your pool suitable for bathers and to protect pool surfaces and equipment from damage, the pH of pool water should be maintained between 7.2 and 7.8. To help reduce pH drift and variable changes when adjusting pH by testing the Total Alkalinity each week maintaining it between 60 and 120 ppm.</p> <ol> <li>Test for pH each time sanitizer is added using a reliable test kit.</li> <li>Be sure the skimmer is empty and does not contain any chemical residue or debris.</li> <li><strong><i>(Skimmer Application)</i></strong> - Add 1 pod directly into the pool skimmer while the pump is running. Allow the pod to dissolve before before adding additional additional pods or other pool products. Only add 1 pod at a time.</li> <li><strong><i>(Pool Application)</i></strong> - Add appropriate number of pods to the deep end of the pool with the circulation system on. Disperse any undissolved chemical from the bottom of the pool with a pool brush until the chemical is dissolved completely.</li> <li>Add an appropriate number of pods as designated in the list above to raise and maintain the pH between 7.2 and 7.8.</li> </ol></div>

<p>Poolife Phosphate Remover Features: <br></p><ul><li><p>Eliminates phosphates from pool chemicals, fertilizers, cleaners, and other pollutants</p></li><li><p>Concentrated formula</p></li><li><p>Helps balance pool chemistry</p></li><li><p>Helps salt generators work efficiently</p></li><li><p>Dosage guide</p></li><li><p>32 oz</p></li></ul><p>Directions for Use:<br></p><ul><li><p>See dosage guide on bottle.</p></li><li><p>32 ounces removes 1,000 ppb in 20,000 gallons of water.</p></li><li><p>For weekly maintenance, add 1 fluid ounce per 5,000 gallons of pool water to maintain phosphate levels below 125 ppb.</p></li></ul>

<div class="product-dosage"> <h2>Dosage</h2> <h3>Intial Treatment for Clean Pools:</h3> <p>8-12 fl oz per 10,000 gallons of water.</p> <h3>Intial Treatment for Pools with Algae:</h3> <p>16-24 fl oz per 10,000 gallons of water.</p> <h3>Black Algae Control:</h3> <p>16 fl oz per 10,000 gallons of water.</p> <h3>Maintenance Dose:</h3> <p>4-8 fl oz per 10,000 gallons of water.</p> </div> <hr class="bs-docs-separator" /> <div class="product-directions"> <h2>Directions</h2> <p>Shake well before using.</p> <h3>Initial treatment for prevention of algae growth in clean pool water.</h3> <p>Use 8-12 fl oz of this product for every 10,000 gallons of water.</p> <h3>Initial treatment for pool with visible established algae:</h3> <p>Use 16 to 24 fl oz of this product for every 10,000 gallons of water. Remove dead algae by vacuuming.</p> <h3>Black Algae Control:</h3> <p>Apply 16 fl oz for every 10,000 gallons of water when algae fist appears. Brush spots daily to remove dead algae. Vacuum out settle algae.</p> <h3>To maintain pools free of visible algae growth:</h3> <p>Use 4 to 8 fl oz of this product per 10,000 gallons of water weekly.</p> <h3>Method of Application:</h3> <p>Never mix concentrated product with other concentrated pool chemicals such as concentrated dry or liquid chlorine. When properly diluted Poolife Defend+ is compatible with those chemicals normally used to treat pools.</p> <ol> <li>Shake well before measuring out required amount of Poolife Defend+.</li> <li>Apply directly to the pool water with the circulation system turned on. <p>Allow at least one hour for product to be distributed before turning off the pump.</p> </li> <li>Repeat treatment until control is evident.</li> </ol></div>

<h2>Product Information</h2> <p>Poolife pH Plus is used to raise pH levels in pool water. It helps prevent corrosion of metal fixtures and hard surfaces in your pool. Poolife pH Plus is composed of white, odorless granular sodium bicarbonate, also known as “soda ash.”</p> <h3 class="features">Product Benefits:</h3> <ul> <li>To raise pH levels</li> <li>Broadcast widely over the deep end of the pool with water circulating</li> <li>pH Plus can also be pre-dissolved and added as a liquid</li> <li>If so, it is recommended you add the liquid as you walk around the sides of the pool’s deep end</li> </ul> <h3 class="features">Dosage/Frequency:</h3> <ul> <li>Use as needed to raise pH level</li> <li>For dosage requirements, measure current pH then refer to product label for proper dosage</li> <li>The ideal pH range for your pool is 7.2 to 7.8, so use if pH level is lower than 7.2</li> </ul>

<h2>Description</h2> <p>Poolife Flocculant eliminates hazey and cloudy water. Haze is usually made up of finely divided particles such as clay, silica, or organic material, which may be too small for the filter to remove. A flocculant helps to coagulate these particles, thus facilitating their removal from the pool and leaving your water crystal clear. This product can be used as a flocculant or as a filter aid, depending on the severity of the cloudiness.</p> <hr /> <h2>Features</h2> <ul> <li>Eliminates water haze</li> <li>Eliminates cloudy water</li> <li>2.25 lbs</li> </ul> <div><hr /></div> <div> <h2><span style="font-size: large;">Contains</span></h2> </div> <div> <ul> <li>Aluminum Sulfate</li> </ul> <div><hr /> <h2><span style="font-size: large;">Directions</span></h2> <br /> <ul> <li>For Sand Filters, add 8-12 ounces.</li> <li>For Cartridge Filters, add 8-12 ounces.</li> <li>For D.E. filters, add 1-2 ounces.    <br /><br /><strong>Note:</strong> Dosage recommendations are for standard filters managing 10,000 to 35,000 gallons of pool water.</li> </ul> <div></div> </div> </div>

<p></p> <p><span>Poolife Enzyme for Pools quickly removes unsightly scum lines while protecting your filters from oily build-up and clogging. It also reduces maintenance on tile, filters, and other pool surfaces. This product is compatible with any type of pool sanitizer.</span></p> <hr /> <p><br /><span>Poolife Enzyme for Pools Features:</span></p> <ul> <li>Quickly removes scum lines</li> <li>Protects filters from oily build-up and clogging</li> <li>Reduces maintenance</li> <li>Compatible with any type of pool sanitizer</li> <li>1/2 Gallon / 64 fl. oz.</li> </ul> <div><hr /></div> <p><span>Directions for Use:</span></p> <ul> <li>Add 16 oz per 10,000 gallons of pool water twice a week until scum lines are gone.</li> <li>To prevent oils, lotions, and other organics from accumulating on walls or in the water, add 8 oz per 10,000 gallons of pool water every other week. Can be added weekly during periods of high usage.</li> </ul> <p><span>Poolife 62063</span></p>

<h2><span style="font-size: 1.5em;">Product Information</span></h2> <div class="tab-pane-content"> <p>Sunlight exposure can deplete your pool of its proper chlorine supply. Poolife Stabilizer and Conditioner is a slow dissolving granular product that protects your pool from sunlight. This will extend the time chlorine remains in your pool and provide added protection against bacteria &amp; algae.</p> <h3 class="features">Product Benefits:</h3> <ul> <li>Should be added slowly through the skimmer</li> <li>As water circulated through the skimmer, the water’s turbulence helps dissolve the chemical</li> <li>Any remnants of product that do not fully dissolve will dissolve on the filter components</li> <li>Premature backwashing may wash away any un-dissolved Cyanuric Acid - the active ingredient in Poolife Stabilizer and Conditioner</li> <li>After applying product, wait at least 48 hours before backwashing</li> <li>It is recommended to backwash the filter prior to adding this product</li> <li>Be careful not to add product too quickly as this may clog the filtration system</li> </ul> <h3 class="features">Dosage/Frequency:</h3> <ul> <li>This product is very insoluble (slow dissolving)</li> <li>As such, it may take weeks to dissolve completely</li> <li>For ideal conditions, maintain a stabilizer level of 20 - 50 ppm</li> <li>Use 16 oz. per 10,000 gallons</li> </ul> </div>

<div class="product-dosage"> <h2>Dosage</h2> <h3>If Total Alkalinity: 50 ppm Range:</h3> <ul> <li>pH 7.0 add 8 oz per 10,000 gallons of water.</li> <li>pH 6.6 add 48 oz per 10,000 gallons of water.</li> <li>pH 6.4 add 80 oz per 10,000 gallons of water.</li> </ul> <h3>If Total Alkalinity: 100 ppm Range:</h3> <ul> <li>pH 7.0 add 12 oz per 10,000 gallons of water.</li> <li>pH 6.6 add 92 oz per 10,000 gallons of water.</li> <li>ph 6.4 add 144 oz per 10,000 gallons.</li> </ul> </div> <hr class="bs-docs-separator" /> <div class="product-directions"> <h2>Directions</h2> <h3>Before Adding this Product:</h3> <ol> <li>Meausre the pH of pool water with a Poolife 6-way Test Strip.</li> <li>The pH should be measured each time a sanitizer is added.</li> <li>Use the dosage reommendations to determine the correct amount of this produt.</li> </ol> <h3>How to add this product to your pool:</h3> <ol> <li>Scatter this product over the pool surface.</li> <li>Keep the circulationg pump running.</li> <li>Check the pH again after 2 hours.</li> <li>Repeat treatment if necessary.</li> </ol></div>

<div class="product-description"> <h2><strong><span style="font-size: 12px;">Poolife pH Minus lowers the ph level in your swimming pool. pH levels should be maintained in the range of 7.2-7.6 ppm.</span></strong></h2> </div> <hr class="bs-docs-separator" /> <div class="product-dosage"> <h2>Dosage</h2> <h3>Lower ph:</h3> <p>If ph is 7.6-7.9 add 8 oz per 10,000 gallons of water..</p> <p>If pH is 8.0-8.4 add 16 oz per 10,000 gallons of water.</p> <p>If pH is above 8.4 add 24 oz per 10,000 gallons of water.</p> <h3>Lower Alkalinity:</h3> <p>2 lb per 10,000 gallons of water to lower alkalinity by 10 ppm.</p> </div> <hr class="bs-docs-separator" /> <div class="product-directions"> <h2>Directions</h2> <h3>To lower pH</h3> <ol> <li>Measure the pH of pool water with Poolife 6-Way Test Kit.</li> <li>Follow product dosage directions to determine correct amount of this product.</li> </ol> <h3>Usage:</h3> <p>Broadcast this product over the deepest part of the pool. In shallow pool (4 ft or less) dissolve product in a pail of water before adding to pool. Always add product into water.</p> <h3>How to Lower Alkalinity:</h3> <p>Keep the total alkalinity betwen 60-120 ppm. Each month, test for total alkalinity with Poolife 6-Way Test Kit. If alkalinity is high:</p> <ol> <li>Add 2 lb of this product for each 10,000 gallons of pool water to lower alkalinity 10 ppm.</li> <li>Keep the ciculation pump running.</li> <li>Add this product in one spot at the deep end of the pool.</li> <li>Do Not apply near walls and metal fixtures.</li> <li>Repeat each day until desired alkalinity is reached.</li> </ol></div> <hr class="bs-docs-separator" /> <div class="product-ingredients"> <h2>Ingredients</h2> Sodium Bisulfate: 92%, <strong>Constituents Ineffective as adjuvants: </strong>8%</div>

<h2>Product Information</h2> <p>Poolife pH Minus is a white, granular form of sodium bisulfate (dry acid). Poolife pH Minus is equally effective at lowering your pool’s pH levels and lowering Total Alkalinity (TA). But it depends on how the product is applied.</p> <ul> <li>Use Poolife pH Minus to lower pH</li> <li>While water is circulating, broadcast widely over the deep end of the pool.</li> <li>If you would like to pre-dissolve and add pH Minus as a liquid, add the liquid as you walk around the sides of the pool.</li> </ul> <h3 class="features">Dosage/Frequency</h3> <h3 class="features">To Lower pH:</h3> <ul> <li>Try to keep your pH levels between 7.2 – 7.8</li> <li>Use this product if pH goes above 7.8</li> <li>Proper dosages will vary</li> <li>The proper dosage is determined by your current pH</li> <li>First, test current pH. Then refer to product label for proper dosage to adjust pH</li> </ul> <h3 class="features">To Lower Total Alkalinity:</h3> <ul> <li>Add the product in one localized area at the deepest end of the pool: this will create a localized pocket of low pH, which will lower your total alkalinity</li> <li>Total alkalinity (TA) should be in the range of 80 – 120 ppm</li> <li>Adding 2 lbs. per 10,000 will lower TA by 10 ppm</li> <li>Do not exceed 2 lbs. per 10,000 gallons per day: if additional adjustment is needed, add the following day</li> </ul> <p><i>*</i>Important* Remember, do not broadcast. The key is to add the acid in one isolated area</p>

<p><span style="font-size: medium;">Poolife® Alkalinity Plus Balancer</span></p> <div class="description"> <p><span style="font-size: medium;">Poolife® Alkalinity Plus balancer raises the total alkalinity of swimming pool water. The ideal total alkalinity range is 60-120 ppm. Maintaining total alkalinity below 60 ppm may cause the pH to fluctuate excessively.</span></p> <h3><span class="heading4" style="font-size: medium;">Useful Tips</span></h3> <ul> <li><span style="font-size: medium;">Test total alkalinity weekly and add this product if total alkalinity is below 60 ppm.</span></li> <li><span style="font-size: medium;">Use convenient dosage chart on product label.</span></li> <li><span style="font-size: medium;">Always adjust total alkalinity prior to adjusting pH.</span></li> </ul> <div><span style="font-size: medium;"></span></div> <div><span style="font-size: medium;"></span></div> <div><span style="font-size: medium;"><br /></span></div> <div><span style="font-size: medium;"><span style="font-size: medium;"></span></span> <h2>Dosage</h2> </div> <div><span style="font-size: medium;"><span>1.5 lb per 10,000 gallons to raise total alkalinity 10 ppm.</span></span></div> <div><span style="font-size: medium;"><br /></span></div> <div><span style="font-size: medium;"><span style="font-size: medium;"></span></span> <h2>Ingredients</h2> </div> <div><span style="font-size: medium;"><strong>Sodium Bicarbonate: </strong><span>100%</span></span></div> <div><span style="font-size: medium;"></span></div> <div><span style="font-size: medium;"><br /></span></div> </div>

<h2>Benefits</h2><ul><li><p>&nbsp; Algaecide and phosphate remover in one</p></li><li><p>&nbsp;Stops algae before it starts</p></li><li><p>&nbsp;Easy to use – no pre-mixing</p></li><li><p>Does not affect water balance</p></li><li><p>&nbsp;No phosphate testing required</p></li><li><p>Swimmers can re-enter the pool 15 minutes after application </p></li></ul><h2></h2>